Deposition of ZnS thin film by ultrasonic spray pyrolysis: effect of thickness on the crystallographic and electrical properties

Zinc sulfide (ZnS) thin films have been deposited on Si (1 0 0) substrate using ultrasonic spray pyrolysis. X-ray diffraction (XRD) analysis revealed that the films are (0 0 2) preferentially oriented with c-axis-oriented wurtzite structure. The crystallinity has been found to improve with film thickness in the 180–6000 nm range. Film structure has been analyzed by XRD, scanning electron microscope, FTIR, and Raman spectroscopies, while the stoichiometry has been verified by energy-dispersive spectroscopy and particle-induced X-ray emission techniques. Electrical properties of the grown films were characterized by current–voltage and capacitance–voltage measurements where, the films show better conducting behavior at higher thickness.     

Relation between Airy beams and triple-cusp beams

Airy beams and triple-cusp beams are two kinds of accelerating beams. The propagation characteristics and internal topological structures of accelerating Airy beams are well understood because of the developed mathematical theory about Airy function. However, limited information is available about the optical characteristics of accelerating triple-cusp beams. In this work, the relationship between Airy beams and triple-cusp beams is examined theoretically and experimentally. Results reveal some important optical characteristics of triple-cusp beams based on the optical characteristics of Airy beams. These findings are expected to provide a foundation for future applications of triple-cusp beams.     

Influence of growth temperature and post-annealing on an n-ZnO/p-GaN heterojunction diode

We report on an n-ZnO/p-GaN heterojunction diode fabricated from zinc oxide (ZnO) films at various growth temperatures (450, 500, 550, and 600 °C) by RF sputtering. The films were subsequently annealed at 700 °C in N₂ ambient. To investigate the influence of the growth temperature of n-ZnO films, the microstructural, optical, and electrical properties were measured using scanning electron microscopy (SEM), X-ray diffraction (XRD), photoluminescence (PL), and Hall measurements. The XRD pattern showed the preferred orientation along the c-axis (002) regardless of growth temperature. The PL spectra showed a dominant sharp near-band-edge (NBE) emission. Current–voltage (I–V) curves showed excellent rectification behavior. The turn-on voltage of the diode was observed to be 3.2 V for the films produced at 500 °C. The ideality factor of ZnO film was observed to be 1.37, which showed the best performance of the diode.     

退火温度对TiO2/CdSe纳米片异质结薄膜光电性能的影响

采用水热法在FTO上制备（001）高活性晶面主导的TiO₂纳米片薄膜,利用循环伏安法在TiO₂纳米片薄膜上沉积CdSe颗粒,制备了TiO₂/CdSe纳米片异质结薄膜。分别在150、250、350、450 ℃,氩气保护气氛中对样品进行退火。利用X射线衍射仪（XRD）、场发射扫描电镜（FESEM）、X射线光电子能谱分析仪（XPS）、紫外-可见（UV-Vis）分光光度计以及电化学工作站对不同温度退火后的TiO₂/CdSe纳米片异质结薄膜的微观形貌、晶体结构、光电化学性能进行表征和测试。结果表明：六方相CdSe纳米颗粒均匀包覆在TiO₂纳米片表面,直径30 nm左右;随着退火温度的升高CdSe纳米颗粒长大,形成光滑的CdSe薄膜,且晶化程度提高;TiO₂纳米片表面的Se元素与Cd元素发生氧化;TiO₂/CdSe纳米片异质结薄膜对可见光的吸收光谱发生红移,禁带宽度逐渐减小。光电化学性能测试表明随着退火温度的升高,TiO₂/CdSe纳米片异质结薄膜的光电流密度显著提高,开路电压减小,但由于SeO2和CdO的出现,导致填充因子减小,影响光电转换效率的提高。在本实验条件下,TiO₂/CdSe纳米片异质结薄膜的最佳退火温度为150 ℃,填充因子为0.77,光电转换效率达到3.12%。     

硼的添加对Ti0.26Zr0.07V0.24Mn0.1Ni0.33贮氢合金结构和电化学性能的影响

Ti_0.26Zr_0.07V_0.24Mn_0.1Ni_0.33Bx(x=0~0.10)系列合金均有V基固溶体相和C14型Laves相两相组成。添加B可提高Ti_0.26Zr_0.07V_0.24 Mn_0.1Ni_0.33合金的放电容量, Ti_0.26Zr_0.07V_0.24Mn_0.1Ni_0.33B0.1合金电极在60 mA·g^-1电流放电时的放电容量达到476.7 mAh·g^-1.B的添加不同程度地降低了合金的高倍率放电性能, 使合金电极表面上电化学反应的电荷转移电阻(R_ct)显着增加, 交换电流密度(I₀)显着降低。添加B可显着改善Ti_0.26Zr_0.07V_0.24Mn_0.1Ni_0.33合金电极的高温放电性能, Ti_0.26Zr_0.07V_0.24Mn_0.1Ni_0.33B_0.025合金电极在343 K高温下其放电容量达到525.6 mAh·g^-1.     

爆炸载荷下脆性颗粒体系破碎特性的数值研究

试验发现,以球形TNT为中心爆源,球形玻璃珠构成的颗粒和球壳中发生破碎的颗粒体积分数随当量比(颗粒球壳的质量与TNT炸药的质量比)的增加呈现指数衰减规律。采用有限元与离散元耦合的连续非连续数值方法,揭示了中心炸药起爆后颗粒环壳内爆炸波的传播衰减和在环壳外界面反射后的稀疏卸载过程。由于爆炸波的短脉冲特性,颗粒内部应力场始终处于应力非均衡状态,采用应力均衡状态下颗粒破碎强度的Weibull分布会得到远高于试验测得的破碎颗粒体积分数。因此采用破坏波传播特征时间内的平均诱导应力而非瞬时诱导应力作为颗粒破碎强度的应力指标,并通过试验结果确定破坏波传播特征时间。考虑了应力传播的非均匀性对于颗粒破碎的影响,得到了平均诱导应力峰值的概率分布随比例距离的变化规律,结合修正后的颗粒破碎强度Weibull分布建立了破碎颗粒体积分数随比例距离的变化模型。     

随机参数智能桁架结构动力特性分析

文中针对随机参数压电智能桁架结构研究了基于概率的结构动力特性分析方法。建立了压电主动檑和被动杆结构材料的质量密度、弹性模量同时具有随机性时结构的刚度矩阵和质量矩阵；从结构振动的瑞利商表达式出发，利用代数综合法推导出结构特征值随机变量数字特征的计算表达式。最后通过两个算例考察了智能桁架结构物理参数的随机性对其动力特性的影响，并获得了一些有意义的结论。     

建筑结构动力特性动点脉动测试

介绍用无人工激励动点测试（动点脉动测试）方法确定建筑物的自振频率，振型和阻尼。使用这一方法对南京电视塔、多层基础隔振房屋及水塔等进行了动力性能测试，获得了满意的结果。     

横观各向同性体应力波传播问题的特征分析

本文根据广义特征理论,对横观各向同性体轴对称弹性波传播问题进行了理论分析。提出了一个简化特征分析的方法,这种方法将成为应用特征线法求解各类各向异性应力波问题的一个突破口。     

Existence and uniqueness of optimal solutions for multirate partial differential algebraic equations

The numerical simulation of electric circuits including multirate signals can be done by a model based on partial differential algebraic equations. In the case of frequency modulated signals, a local frequency function appears as a degree of freedom in the model. Thus the determination of a solution with a minimum amount of variation is feasible, which allows for resolving on relatively coarse grids. We prove the existence and uniqueness of the optimal solutions in the case of initial-boundary value problems as well as biperiodic boundary value problems. The minimisation problems are also investigated and interpreted in the context of optimal control. Furthermore, we construct a method of characteristics for the computation of optimal solutions in biperiodic problems. Numerical simulations of test examples are presented.